Children Bicycle Installation Guide

In the online purchase of children's bicycles, new cars are often carton packaging, the need for a simple installation, the following European and American children's bike to the general situation to tell you about. Before installing the children's bike, please read the instructions carried by the car, the following content is for reference only:

The installation steps are as follows:

(1) instructions and a multi-purpose installation tool (not all suppliers are provided) in a small tray, please remove it before installation.

(2) Please read the instructions carefully before installation

(3) all the parts and the body between the fixed plastic tape (commonly known as squid silk) cut

(4) Install the fence: the fender is left and right, the front nut of the rear axle is unscrewed, and then the long hole of the fender is fitted into the rear axle, and the nut is screwed on a few laps, but do not tighten, The frontal height is 0.5 to 1 cm from the ground and the nut is tightened.


The ideal height of both sides of the ferry is 0.5 to 1 cm off the ground (fence to the height of the ground to the ground), too high will be unstable in the ride, just learn the car to master the child is not good, too low, will be uneven The rear of the road or the rear wheel when the rear wheel overhead, the rear wheel only turn fixed.

During installation, note that the protrusion of the positioning pad on the rear axle is jammed at the notch of the rear fork and then tighten the screws.

Child Bicycle Guard Wheel

(5) to install the front wheel: This is a need to have some effort to work, first the front wheel of the screw off, the front wheel into the front brake into, and the fork into the front axle, The front brake is deformed and the protruding points of the two locating shims on the front axle are placed in the hole at the end of the fork and the two front wheels are tightened. Positioning the placement of the gasket is very important, the role is to ensure that the front fork and the front wheel in the screw after the relaxation will not easily disengage.

(6) Install the handlebar: remove the handle of the handlebar of the handlebar, unplug the black plastic on the riser, pull the riser into the head of the frame, pay attention to adjust the front and rear direction and angle of the handlebar, and then tighten (Not the screws on the carriage), turn the handlebar back and forth, and put the handlebar in the center, then tighten the handlebar and set the screw between the handle.


The depth of the insertion of the head into the frame depends on the height of the baby, if not appropriate to release the hanging screw up and down to adjust to adjust the baby's height. Note that the riser can not be inserted too shallow, the riser has a scale line, to ensure that the scale line in the frame head tube can not be exposed.

After installation check the front brake, you can shake the brake to make it at the center, do not touch the rim. It is also necessary to adjust the tightening screw on the side of the brake (using the live wrench) so that the opening and closing of the brake is appropriate.

For the vehicle with the front and rear tilt adjustment function, the handlebar also needs the following installation and fixing steps.

(7) to install the saddle: the saddle tube into the frame of the seat tube, height can be adjusted according to the height of the baby, and then tighten the screws.


Saddle tube also has a safety line, can not insert too shallow, to ensure that the scale line can not be exposed in the seat tube.

And do not put the saddle tube inserted in the end, to ensure that the saddle tube straight pipe part of a little exposed, or insert the end may cause the seat tube screw can not lock.

(8) Installation foot: The foot is divided into the left and right sides of the foot thread, and R is the right side pedal (viewed from the rear of the car) on the cross section of the foot thread. Pedal, pay attention to tighten the screws after the force must be tight again, in case of not tightening when riding off.

(9) Commissioning: Now your baby's bike has been installed, you can turn the foot to see if the rotation is smooth, test the brake is valid. And then remove all the wrapping paper. Let the baby try to ride to see if the height is appropriate. There is a bell to see whether the car is fixed, or adjust the direction of tightening about. In order to ensure the safety of the baby riding, and finally again check all the installation parts of the screw is fastened. And again after a period of time to check whether there is loosening.

Boy riding a balance car